Converts the documented 230 VAC source to 24 VDC system power.
Technical Summary
PS1000/230 identifies the HIMA PS 1000 power supply execution documented as PS 1000/230/01. HIMA certification data lists 230 VAC input and 24 VDC, 40 A output.
The complete front label, /01 execution, rack or housing and parallel-power arrangement must be reviewed because the shortened PS1000/230 text does not show every service identifier.
Specifications
| Manufacturer | HIMA Paul Hildebrandt GmbH |
|---|---|
| Submitted model | PS1000/230 |
| Documented complete designation | PS 1000/230/01 |
| Product type | Power supply unit |
| Input | 230 VAC |
| Output | 24 VDC |
| Continuous output current | 40 A |
| System context | HIMA HIQuad / approved PS 1000 installation |
| Selection control | Complete label and installed power-distribution arrangement |
Features
Provides 40 A continuous output for the approved HIMA rack and distribution design.
Supports service replacement when the complete PS 1000 execution and housing are matched.
Maintains a defined power-supply identity for redundant or parallel arrangements.
Compatibility
- Confirm whether the front label reads PS 1000/230/01 and record every additional marking.
- Document rack or housing type, AC protective device, DC distribution and any parallel supply units.
- Verify conductor size, polarity, protective earth, cooling and cabinet clearance against HIMA instructions.
- Do not substitute the 115 VAC execution or a later wide-range PS 1000 without an approved migration review.
Replacement
- Isolate both AC input and stored or backfed DC energy before touching supply wiring.
- Measure source voltage, inspect terminals and record the load and redundancy arrangement.
- After replacement, confirm 24 VDC output, fault signaling, load sharing where used and stable rack operation.
- Retain the complete supply label and measured commissioning values in the power-system record.
FAQ
What full label should accompany a PS1000/230 enquiry?
Provide the front and side labels showing whether the unit is PS 1000/230/01, plus housing, rack and neighboring supply details.
Can PS1000/230 replace a PS 1000/115 execution?
No. The certified input voltages differ; use only a documented HIMA replacement or migration path.
What distribution evidence matters before changing PS1000/230?
Record DC load, fuses, cable sizes, parallel units, grounding, alarm contacts and every downstream feed.
How should repeated PS1000/230 faults be investigated?
Check AC quality, DC overload, terminal heating, ventilation, fan condition and backfeed before condemning the supply.
What proves the replacement power path is ready?
Verify stable 24 VDC under normal load, correct fault indication, redundancy behavior and healthy operation of the supplied HIMA system.
About IndustryParts
https://www.industryparts.com/Power-supply enquiries include the complete distribution path
IndustryParts handles PS1000/230 with the /01 label, AC source, DC load and redundancy arrangement visible.
- Input execution checked
- 40 A load documented
- Distribution evidence retained
Recommended Models
| IF787 | Moeller NZM7-100N-M | GCD-0001 |
| Siemens 1FT6084-1AF71-3AH1 | 21F5A3R-YR6A | LOG210 5005-0210 |
| DK32/K1/S | K21R71K4 TLB IEC | KSC-2/HF 031000086 7-450-95-008-5 |
| X20DS1119 | FC-302N160T5E54H4BGC3XXSXXXXALBXCXXXXDX | STI-6400 |
| ULXP4 , 829-865 Mhz-S3 | CS1W-ID261 | AB7834-F |
| OJ5158 | EDS-408A | CA-DW470EN-IR-0360B |
| Dell K20A | MAC071B-0-TS-2-C/095-B-0 | HDC01.1-A040N-PB01-01-FW |
| BNS 250-12Z-2187 | X20SO4110 | SN75461P |
| AD8 | EKI-2525PA | BZMD1-A125 |
| SR3 B101B | SIM-CNR04E | 2201-29400-001 |
