Siemens 6ES7193-6AR00-0AA0 ET 200SP BusAdapter BA 2xRJ45
01Product Overview
Siemens 6ES7193-6AR00-0AA0 is the SIMATIC ET 200SP BusAdapter BA 2xRJ45. It provides one PROFINET interface through two switched RJ45 copper ports and is used on compatible ET 200SP interface modules and CPUs that accept the Siemens BusAdapter format.
02Functions
Core Functions
- Terminates two copper Ethernet connections on a compatible ET 200SP interface.
- The two RJ45 ports operate through the documented integrated switch.
- Supports PROFINET line or ring topologies when the host interface and project design permit them.
- Provides replaceable physical network-interface hardware separate from the host module.
- The 20 mm width preserves the compact ET 200SP station form.
- Copper runs must follow Siemens cable, shielding, connector, grounding, and topology rules.
Product Identity
- Manufacturer: Siemens
- Model: 6ES7193-6AR00-0AA0
- Product Type: SIMATIC ET 200SP BusAdapter BA 2xRJ45
- Review Status: Verified
03Specifications
| Manufacturer | Siemens |
|---|---|
| Article Number | 6ES7193-6AR00-0AA0 |
| Product Type | SIMATIC ET 200SP BusAdapter BA 2xRJ45 |
| PROFINET Interfaces | 1 |
| RJ45 Ports | 2, integrated switch |
| Copper Cable Length | Up to 100 m per documented network segment |
| Operating Temperature, Horizontal | -30 to 60 deg C |
| Operating Temperature, Vertical | -30 to 50 deg C |
| Maximum Operating Altitude | 5,000 m; observe restrictions above 2,000 m |
| Lifecycle | Active product in Siemens SiePortal |
| Country of Origin | Germany |
| Environmental Product Declaration | Available |
04Compatibility
- Use only with ET 200SP interface modules or CPUs that explicitly support the BA 2xRJ45 BusAdapter.
- Confirm the host article number, firmware, PROFINET role, topology, media, port diagnostics, and redundancy protocol.
- Match RJ45 copper media; fiber BusAdapters are different products.
- Observe the 100 m copper-segment limit and the environmental restrictions for the complete station.
- Do not substitute a different BusAdapter solely because it fits mechanically.
05Applications
Typical Uses
- PROFINET connection of ET 200SP distributed I/O stations.
- Two-port line topology between field stations.
- Compact machine and process-network nodes using copper Ethernet.
- Maintenance replacement of an installed BA 2xRJ45 adapter.
Selection Boundary
- Use the exact model and manufacturer identity shown on the installed product.
- Treat application examples as context, not as proof of compatibility.
- Confirm electrical, mechanical, communication, safety, and environmental requirements before ordering.
06Lifecycle
- Siemens identifies 6ES7193-6AR00-0AA0 as an active product.
- Record the host module, station name, IP settings, topology, port assignment, media, cable route, and diagnostics before exchange.
- Power down and follow the ET 200SP removal and installation procedure.
- After replacement, verify link state on both ports, device name, IP configuration, PROFINET communication, topology recognition, redundancy behavior where used, and controller diagnostics.
- A host-interface or media migration requires engineering changes beyond replacing the BusAdapter.
FAQFrequently Asked Questions
What is
6ES7193-6AR00-0AA0 is a Siemens ET 200SP BusAdapter with two switched RJ45 copper ports.
Where is this product used?
It is used on compatible ET 200SP interface modules and CPUs to provide the physical PROFINET connection.
What should be confirmed before ordering?
Confirm the complete model or part number, manufacturer, installed hardware revision, electrical design, interfaces, wiring, approvals, and project configuration.
What information should be recorded before replacement?
Record the host article and firmware, station name, IP settings, topology, port mapping, cable type and length, diagnostics, redundancy protocol, and cabinet environment.
Is another model a direct replacement?
Another BusAdapter must be explicitly supported by the host and must match the required media, ports, topology, environment, and project configuration.
What should be checked after installation?
Verify both Ethernet links, PROFINET device recognition, station name, IP settings, I/O communication, topology, redundancy, and diagnostics.
+Recommended Models
| M0257 | ABB AL9-22-00 1SBL143501R8700 | ITEM3-2000U000080 |
| XEV22D-1P2CO | XS630B1MAL2 | 15HD |
| ABB 3BSE020838R1 3BSE020850R1 | VS481B | IS972LX IS23DI0XCD000 |
| XLSG1-HD | 3TX7014-1BM02 | LTMR100MFM |
| ABB 1SDA054873R1 | MR-52 10278 | PRINT-B-MS5.1-IWG4020.3-0/4 |
| IQ3XCITE/96/100-240 | HP101A-L5W1W | AC53.602.0E AC5360B.0Z |
| 3/25 272786 | VJP-4E | Q.PS-AD2-2402F |
| 1C31203G01 | BMXAMO0210 | DU125,151035020 |
| LNL-1003MK | GHQ6310035R0111 | BR6000-R12PH |
| TS-3106-CI-00-AA | 2580190000 | BZMB1-A100 |
