Siemens 6SL3120-1TE13-0AA4 SINAMICS S120 3 A Single Motor Module
A 3 A booksize Motor Module with a 9 A maximum output, integrated connector and extended Safety Integrated support.
ManufacturerSiemensModel6SL3120-1TE13-0AA4Product TypeSINAMICS S120 3 A Single Motor Module, booksize
01Key Information
Siemens 6SL3120-1TE13-0AA4 is a 3 A SINAMICS S120 Single Motor Module in booksize format. Compared with the earlier AA3 generation, the AA4 data sheet documents a 9 A maximum current while retaining the 3 A rated output, 2.6 A base-load current and 3.5 A S6 current. The exact article is now presented by Siemens as a spare part, and its integrated motor connector and hardware generation must be included in any replacement review.
Configuration CheckMatch the complete article number, hardware generation, electrical design, connections, firmware and installed-system requirements.
02Functions
Documented Functions
- Controls one motor axis from a 510 to 720 V DC link.
- Delivers 3 A rated current, 3.5 A S6 current and up to 9 A maximum current.
- Provides optimized pulse patterns for the motor-side inverter output.
- Supports extended Safety Integrated functions to SIL 2, PL d and Category 3 as documented.
- Uses an integrated X1 connection plug and internal air cooling.
- Carries DRIVE-CLiQ communication for integration into the S120 drive lineup.
Exact Product Identity
- Manufacturer: Siemens
- Model: 6SL3120-1TE13-0AA4
- Product Type: SINAMICS S120 3 A Single Motor Module, booksize
- Status: Siemens identifies the exact article as a spare part
03Specifications
| Manufacturer | Siemens |
|---|---|
| Article Number | 6SL3120-1TE13-0AA4 |
| Product Type | SINAMICS S120 Single Motor Module |
| Construction | Booksize, internal air cooling |
| DC-Link Voltage | 510 to 720 V DC |
| Electronics Supply | 24 V DC, -15% / +20% |
| Rated Output Current | 3.0 A |
| Base-Load Current | 2.6 A |
| S6 Current (40%) | 3.5 A |
| Maximum Current | 9.0 A |
| Rated Power | 1.6 kW |
| Rated Pulse Frequency | 4 kHz |
| DC-Link Busbar Capacity | 100 A |
| 24 V Busbar Capacity | 20 A |
| Motor Cable Length | 50 m shielded / 75 m unshielded |
| Degree of Protection | IP20 / UL open type |
04Installation
- Verify the AA4 suffix, because AA3 and D-type AD0 modules have different documented performance and replacement conditions.
- Use the integrated X1 motor connection and M5 PE connection specified for this exact module.
- Maintain the 50 m shielded or 75 m unshielded maximum motor-cable limit.
- Provide the required internal cooling airflow and keep the 0 to 40 degrees C non-derated operating range.
- Load and verify the correct S120 drive object, pulse-frequency settings and Safety Integrated parameters.
- Complete a safety acceptance test whenever safety-relevant hardware or configuration is replaced.
05Lifecycle
- Siemens current comparison information identifies the exact AA4 article as a spare part.
- The active 3 A D-type article is 6SL3120-1TE13-0AD0, but its suitability must be checked against the installed generation.
- AA4 is not interchangeable with AA3 solely because both are rated 3 A.
- Record the integrated connector, DRIVE-CLiQ cable, firmware and safety configuration before exchange.
- Use current Siemens migration and spare-part guidance for the complete drive lineup.
