Siemens 6ES7151-1AB05-0AB0 ET 200S IM151-1 FO Standard Interface Module
01Technical Summary
Siemens 6ES7151-1AB05-0AB0 is the IM151-1 FO Standard interface module for a SIMATIC ET 200S distributed I/O station. It connects the station to PROFIBUS DP over the integrated fiber-optic interface, supports data rates up to 12 Mbit/s, and manages up to 244 bytes of input data and 244 bytes of output data. A station can include up to 63 supported power, electronic or motor-starter modules, making configuration limits and the installed ET 200S module sequence essential replacement checks.
02Specifications
| Manufacturer | Siemens |
|---|---|
| Article Number | 6ES7151-1AB05-0AB0 |
| Product Designation | IM151-1 FO Standard |
| Distributed I/O System | SIMATIC ET 200S |
| Bus Protocol | PROFIBUS DP |
| Physical Bus Interface | Integrated fiber optic |
| Transmission Rates | 9.6 kbit/s to 12 Mbit/s |
| I/O Address Space | 244 bytes input / 244 bytes output |
| Maximum Connected Modules | 63 supported power, electronic or motor-starter modules |
| SYNC / FREEZE | Supported |
| Direct Data Exchange | Supported |
| Cycle Synchronization | Not supported |
| Firmware Update | Via PROFIBUS DP with STEP 7 |
| Rated Supply | 24 V DC |
| Power-Failure Bypass | At least 20 ms |
| Typical Current Consumption | Approximately 200 mA |
| Typical Power Dissipation | 3.3 W |
03Features
Key Functions
- Links an ET 200S station to PROFIBUS DP through fiber-optic media.
- Supports standard PROFIBUS DP rates from 9.6 kbit/s through 12 Mbit/s.
- Provides 244 bytes of address space in each direction for the configured station.
- Supports SYNC, FREEZE, direct data exchange, identification and maintenance data, and option handling.
- Allows firmware updating over PROFIBUS DP with STEP 7.
- Local SF, BF and ON indicators support fault, bus and supply diagnostics.
Identification
- Manufacturer: Siemens
- Model: 6ES7151-1AB05-0AB0
- Product Type: SIMATIC DP ET 200S IM151-1 FO Standard interface module
- Status: Legacy ET 200S interface
04Compatibility
- Confirm the exact IM151-1 FO Standard article; copper PROFIBUS and PROFINET interface modules use different network media.
- Verify the optical connector, fiber type, segment design, bus address, baud rate and diagnostic behavior.
- Check the complete ET 200S station order, power modules, terminal modules, electronic modules and motor starters against the 63-module limit.
- Confirm that the 244-byte input and output address spaces cover the installed configuration.
- Retain the GSD or STEP 7 hardware configuration, device address, diagnostic mapping and option-handling settings.
- The module does not support cycle synchronization; applications that require isochronous operation need a different verified architecture.
05Replacement
- The IM151-1 FO Standard is a legacy ET 200S interface; confirm Siemens spare-part or repair availability.
- Back up the station configuration and document the optical bus, address, baud rate, module sequence and power-group layout.
- Inspect and clean fiber connectors using the approved procedure before replacing the interface module.
- Do not migrate to ET 200SP, PROFINET or a copper PROFIBUS interface without redesigning network, hardware and PLC configuration.
- After replacement, verify supply, optical bus status, station diagnostics, every I/O module, motor starter and process sequence.
06FAQ
What is Siemens 6ES7151-1AB05-0AB0?
It is the IM151-1 FO Standard fiber-optic PROFIBUS DP interface module for ET 200S.
What is the maximum PROFIBUS rate?
The module supports transmission rates up to 12 Mbit/s.
How much I/O data can it handle?
The documented address space is 244 bytes for inputs and 244 bytes for outputs.
How many station modules are supported?
Up to 63 supported power, electronic or motor-starter modules can be connected, subject to the station rules.
Does it support cycle synchronization?
No. The technical data identifies SYNC and FREEZE support but not cycle synchronization.
What should be checked after replacement?
Check optical bus status, PROFIBUS address and rate, station diagnostics, the complete module sequence and all process I/O.
+Recommended Models
| OC-FP/FP-LS4-MPX-040-CSO90 | CKA-37 H-7PRCD 0861G - PC4404 | PR 4114 4501 |
| T8424D1016 | MT1963-1002 | K1241 |
| MS-16DI | XTCEC012B10TD DILM12-10 | SQ121B6220 |
| OCR/NG0 NG5 1405120010 | 03671 | 6SL3244-0BB12-1FA0 CU240E-2PN |
| IMC-21-S-SC 3093015000081 | VFC-131 | MWR-SH11UN |
| B100 | CLTG38L01 | F124x04 Fnr 07400030 |
| 837447005 737 839-001 G00 | SMC5500/S SMC5500050407 | TA200DU-90 1SAZ421201R1001 |
| PN:50123684-001FRE | 412-AC-RC | LD5 |
| MTL 5573 | CGA-0002 | 79CM30772 |
| BTICINO 346020 | ABB B21311-100,2CMA100154R1000 | PM2100 METSEPM2120 RS485/CI1.0 |
